Archive through March 16, 2010

[tgipe]

want to by rear hitch plate and spring assist for 1535 call or email Tim, 815 718 2246 thanks.

 

[ttheobald]

looking for a GT54 model no 324-190 54" mower deck call 309 467 2676 or email to [email protected]

 

[elthomas]

I need a good carburetor from a k301, cub 128 or equivalent, one that runs good. I need to get my cub up and running better incase kohler decides not to honor warrenty on my husqvarna.

 

[pszollosy]

anybody in florida or nearby have a good used starter/generator for sale?

 

[sschrobilgen]

I'm looking to mate my new plow to my 102, so I believe I need a sleeve hitch? I don't know the make of the plow as there aren't any identifying marks. I would need it shipped to Colorado 80503.
Thank you!
[email protected]

 

[rwdeitrick]

I looking for a complete IH 3 point hitch for a wide frame 129. If any one has 1 please email me at [email protected] Thanks

 

[kmcconaughey]

Scott S., yes you will need a sleeve hitch adapter. Looks like you are also missing the upper cast link for the rear lift.

Also, in case you don't know, that "L" bracket with the two holes in it, that's on the lower part of the axle tube is for the IH Blade/Rake combo. There should be a matching "L" bracket on the other side. The "L" brackets are for connecting springs to assist with lifting the blade/rake. Here's a page from the manual for the blade/rake that shows it. All just in case you were wondering what those brackets were for...

 

[elthomas]

Looking for a good carburetor for a cub 128 with the k301 engine block.

 

[elthomas]

Well it looks like i may need to find a new engine for a cub 128 it's the k301. I live in North Carolina.

email me if you have one near or can help ship, also to discuss a amount.

email: [email protected]

 

[myoungquist]

Wanted to buy for Cub Cadet 147.
Seat, coil, drive shaft guard.
These items need to be shipped.
Please send info to:
[email protected]

 

[klindstedt]

I'm looking for the hydraulic lift supply line for my 1811. While using "Blunier ramming speed" on the last heavy snowfall this year, I had a flex coupling tear apart and then the driveshaft wrapped the supply line around itself. My line (should) look like the one in the picture shown. However, the Cub Cadet parts lookup shows a different configuration for this line...? Let me know what you have and what you want for it - shipped to Chesterton, Indiana 46304

Thanks!

 

[rdehli]

looking for a good 782 cub close to Iowa...Wisconsin... Minesota ... or Northwestern Illinois

 

[rdehli]

looking for a good harness for my 100 project

 

[jbailey]

I broke the right side carrier axle assembly on my 2182. The part number in the parts lookup is 903-1788. This is for the aluminum rear axle used from models 1440 to 2284. If someone has a broken rear axle with a good right side axle extension please call 563-249-2477.
Thanks
Jim

 

[whecht]

I am looking for a plow that will fit my 1972 109 I Live in N/E Indiana you can email me at [email protected].

 

[kshultz]

Willis,
Is it a plow for the back for your garden that you are looking for or a snow blade for the front?

 

[kjgibson]

Looking for an "Idler Pulley Assembly" for a 124.

Thanks!
Kenny

 

[rderamon]

Looking for a drive pulley for a Tupe 1 tiller. Part number is 485-267-R1. Please call (914) 443-4353. Thank you. Rod

 

[jdeshazo]

looking for the exhaust ducts top and bottom for a 782 thanks
josh

 

[jott]

QA-38 mower deck. closest to se wiscosin as possible