Archive through February 14, 2016

[rciminieri]

I am looking for the lift rod for my original labeled #8 and the bracket that goes to the chassis labeled #9. The rod is a must but the other piece will replace my old worn one. Bob 6312950604 or [email protected]

 

[digger]

Bob,
You don't have to look to hard or far.
Click the Xtrememotorworks tab above or this link and buy one.
CLICK HERE

 

[rciminieri]

I did give them a ring. Left a message and i know i will hear back. The bracket i have was cut and bolted back together.... Basically somebody had a great idea haha. Would like to get the bracket as well. I will click backbon and see if they repro them too. Thanks charlie!

 

[digger]

Websites most generally reply faster if they get an email.

 

[dschwandt]

WANTED:
For my 126 resto. A decent usable dash/cowl instrument panel from a 107, 106, 126, 127, or 147. This is the fiberglass part.

The one I have, that is/was supposedly NOS, I have just noticed that someone has hogged the holes out in the fiberglass so big, that the ammeter and grommet for the steering tube just fall through the holes. Either that, or it was defective from the mfgr and returned to the parts depot.
Or, can someone suggest a way to repair this.
Thanks Gang!

 

[dschwandt]

WANTED:
For the 126.
A decent, straight dash tin. The part that the dash decal adheres to.
the 126 and the 106 share this part according to the parts book.

Thanks Again!

 

[jlspicer]

Still looking for an IH 54 inch hydraulic angle blade. Will buy a blade outright without a trade for the Haban blade. Shoot me an email if you've got one (in profile). Thanks!

 

[rciminieri]

Thanks to all I got my lift rod for my O. Still in the market for the sleigh looking bracket for the trip plow if anyone has anything around. Thanks again

 

[wsdrake]

Hi,

I need a few things for my 108. I am looking for a nice fender, and I am looking for this (not the lens):

Also, if you have the left steering spindle available, I may be interested in that (3/4 inch shaft).

Email [email protected]; I am now located in West Virginia, about 1 hr (or so) North of Charleston. Thanks!

 

[rciminieri]

Looking for a good running original with mower deck. Must run well and deck solid and quiet. Nothing'special is good. Don't want to beat up my early one. Will travel ny nj pa ct ma ri.
Thanks to mike in mass for my new blade for my 4 digit.
Bob 6312950604 woodduckdesigns@ yahoo.com

 

[psullivan]

Looking for the aux hydraulic kit for a 1450, or some instructions for making a functional equivalent. Needed to power the 2-way front blade.

 

[kshultz]

Looking for the drive chain for a QA-42A snow thrower. Thanks!
It goes on here.

 

[digger]

Shultzie,
So can we assume your looking for a used one?

 

[kshultz]

Charlie,
Yes, a used one will be fine. (I know where to get a new one

)

 

[dschwandt]

WANTED:
A decent rebuildable #26 carb or throttle lever and dog parts to restore mine. This carb was on the 126 I am restoring. I would sure like to salvage it. Thinking this is the correct #26 carb for the 1x6 1x7 series NF's??

 

[gjmartin]

looking for a Cozy cab enclosure for my 1650 QL

 

[ajtimm]

I am looking for one or two decent front tires for Original. Would consider with or without rims.
THANKS

 

[tsdeese]

I am looking for a decent shape pan seat for a model 70 tim 7049858436

 

[sshaff]

I need a good pan seat for my 100. Let me know what you've got and how much. Thanks!

 

[sbauer]

Looking for a Sims cab for my 982