Monkeying around in Shultzie's garage

[jack casey]

Exactly. When I lived on Long Island (lower NY) the snow would come down heavy and wet but the air temp and ground never really got cold for too long. I can see that the Gent from Pearl River probably has that same scenario. So, you can away with Ags. But where I am now, ice cold, hard rubber, would just chatter over a hard pack ground that's hasn't seen as high as 5 degrees in weeks. When the ground is that hard, you need cutting steel. Sometimes even they won't bite in enough. Added weight or not.
The pic shows 4 link V chains. I added to them, they are 2 link now.
Even the backhoe needs chains for when we get the real snowfall

I shud have been more transparent and must agree with Tony. Coordinates in Pearl River are 41 degrees N and 74 degrees W, not freez-ass where he lives now. I hated the nuisance of taking chains on/off and mowing with chains just brings lotsa dirt in the shed. So, living in a temperate zone, for the last 23 years I used them Carlisle's at 10+ psi (no more) and 160 lbs out back. In 2019 we had a mammoth storm of 25 inches, my 12 HP Elec-Trak moved it, no skids. I shud also say that our driveway pitches 3" to the street.
Cheers and Merry Christmas, Jack

 

[BHAM]

On yet another note.....
Charlie I think you need to be contacting Anheuser Busch on behalf of all of us here about these new beer cans. Yeah it's good to salute the farmers, but why just the ones that drive those green tractors?
View attachment 149251

Don’t you ih people drink Budweiser ?

 

[-CӞ]

I shud have been more transparent and must agree with Tony. Coordinates in Pearl River are 41 degrees N and 74 degrees W, not freez-ass where he lives now. I hated the nuisance of taking chains on/off and mowing with chains just brings lotsa dirt in the shed. So, living in a temperate zone, for the last 23 years I used them Carlisle's at 10+ psi (no more) and 160 lbs out back. In 2019 we had a mammoth storm of 25 inches, my 12 HP Elec-Trak moved it, no skids. I shud also say that our driveway pitches 3" to the street.
Cheers and Merry Christmas, Jack

Elec-trac = full-torque right now, vertical torque curve !!!

 

[kshultz]

I replaced the blades on the zero turn. Has anyone used these on there mower? These are a little thicker than the stock ones. I hope they hold up better.

 

[PACub100]

I replaced the blades on the zero turn. Has anyone used these on there mower? These are a little thicker than the stock ones. I hope they hold up better.
View attachment 156774
View attachment 156775

Good grief man!...you got every penny's worth out of those old ones...

 

[kshultz]

Yeah, my wife is pretty rough on blades. LOL

 

[jbratton]

Yeah, my wife is pretty rough on blades. LOL

You’re that type of guy? LOL

Just kidding!

 

[kmcconaughey]

Those look like the old Gator mulching blades. I've used them before, they work great. They really chop up the clippings and turn dry leaves to dust.

 

[Eric Wittersheim]

The Gator blades didn't cut well on my Ferris ISX800. I swapped back to stock and got a much better cut. I haven't used the Gators on my Cubs.

 

[RAllison]

I replaced the blades on the zero turn. Has anyone used these on there mower? These are a little thicker than the stock ones. I hope they hold up better.
View attachment 156774
View attachment 156775

My blades look like that after every season,lots of sand and pine needles. I have a set of mulching blades on the way for my o-turn as well, curious to see if they wear any better

 

[kshultz]

Sharpened the blades on the 100. Cuts much better now.

 

[RAllison]

Sharpened the blades on the 100. Cuts much better now.
View attachment 156930

How'd you like the new mulching blades? I love mine!

 

[kshultz]

How'd you like the new mulching blades? I love mine!

Actually I think they need sharpening too. When I put them on they didn't seem too sharp, but I thought what the heck, they are brand new. I'll keep you posted after we mow again after sharpening them.

 

[kshultz]

Also last year my Cub started making a noise like a bearing was going out somewhere on the engine. Hopefully it's nothing serious. Maybe water pump, or alternator? I'll find out more later. Been a busy weekend. So it's back in the shop.

Someone's fine wiring job on the headlights. Maybe that's why they don't work if there is more wiring like this. LOL

 

[RAllison]

Also last year my Cub started making a noise like a bearing was going out somewhere on the engine. Hopefully it's nothing serious. Maybe water pump, or alternator? I'll find out more later. Been a busy weekend. So it's back in the shop.
View attachment 156931
Someone's fine wiring job on the headlights. Maybe that's why they don't work if there is more wiring like this. LOL
View attachment 156932
View attachment 156933
View attachment 156934

Now that beast just looks like fun!

 

[jbratton]

How'd you like the new mulching blades? I love mine!

You got mulching blades on your cub? Where did you find those at?

 

[RAllison]

You got mulching blades on your cub? Where did you find those at?

You got mulching blades on your cub? Where did you find those at?

O-turn

 

[PACub100]

now that's a new way to use high tensile wire crimps...

 

[kshultz]

I think I found the problem. The hub assy. for the fan.

 

[kshultz]

I got a new (new to me) replacement fan hub assy. and just got some new belts to put on.
However the Cub project is on hold because of some storm damage clean up from the Tuesday storm. I had two large limbs come down, thankfully the wind was blowing away from the house. I just had this tree quoted to be removed last week. I guess I need to get it requoted now. (LOL) The hail pic is from my friends house just about 2 miles down the road. That was after about 20 minutes of melting. They had a few windows broken out and damage to their siding. We had hail but not that big. Try to get the rest picked up tonight.