Archive through May 23, 2011

[jcook]

Hello, I am looking for a 1200 w/creeper in good shape. No trailer queens, but good condition. Also, a 1250 in same shape. Have trades of same and/or cash as needed. TIA Jim C

 

[jmills]

i am looking for starter generator bracket for a k181 the one that bolts to the side of engine thanks

 

[sbauer]

A 46gt deck.

 

[rodsmith]

On my 1962 ORIGINAL the PO has cut and chopped up the steering tower. It can be fixed, but I think it would be easier to replace if I can find a GOOD one CHEAP. Don't have any idea what they are worth.Wouldn't mind finding throttle control and correct key switch also.(CHEAP)
rodsmith6@ att.net
ROD

 

[jgibson]

I am looking for the lift assembly for a Haben 60" deck to go on a 2072. Also looking for a step guard for the same deck, and of course there are some smaller items too. Basically all I have is the deck. Thank You!

 

[aclark]

Does anyone have a twin 17 Kohler that will fit 1983-682. If so can you call me

Anthony 859/621/8774

 

[bbrush]

looking for the fuel line that goes from the tank to the sediment bowl on a cub cadet original if you can help please e mail Bob at [email protected]

 

[thoffman]

Bob "B", the hardward store has lots-o-copper line. Just cut and bend what you need

 

[bbrush]

i know tom but my original did not have the correct fuel line to begin with if i had one here to copy i could make one for sure i want it to be rite i have a whole lot of time in this thing

 

[pburkle]

I am looking for an IH #4 dump/hauling cart. Also looking for a pair of ORIGINAL 44A mower deck gauge wheels in good or mint condition. Top dollar paid for these items !! Thanks !!

Paul

 

[dross]

Bob, what about trying this. Does anybody have a picture of the fuel line installed on an Original, sure would apprecieate it guys. Thanks.

 

[aschumacher]

BOB, DAVE, this looks like a question that should posted on the regular Forum. More likely to get some sort of help there. Remember this is a long weekend, info maybe in short supply for a few days.

 

[jdudding]

I am looking for a gear shifter for a 1806 cub cadet.TIA,Joey.

 

[thoffman]

A shot of the old and new.

 

[bmcanulty]

I am looking for a manual PTO for a Model 70 Cub Cadet. I would like to find a new or rebuilt clutch. Thanks, I'm in TX., but will pay the shipping from anywhere. E-mail me at [email protected] with info...Thanks Again

 

[sbauer]

i need a wiring harness for a 982

 

[kbirkmann]

I am looking for a sleeve hitch for a 782 (wide frame)also a small plow that will fit the 782. Also a used Kohler Mag engine in running condition, that will fit the 782. Email to [email protected]

 

[rpratt]

I am looking for a Brinly Sleeve Hitch Cultivator with wheels. Please email me at [email protected] if you have one that you want to sale. Thank you.

 

[jstorma]

Hi,

I have a 42" dozer blade and I'm looking for a good used sub frame to fit a 782 or 1650, and if availible a lift rod. Shipping will be to 54313 in WI. If close by I can pick up in the area.

Please email me.

Thanks,

Jim

 

[cmiller]

I'm looking for a clean, low-hours, CCC 2072 SGT. I am located near Philadelphia; you must be within a day's drive for me. Let me know what you have.

Thanks,
Chris
[email protected]