Archive through January 13, 2014

[mgerecke]

Looking for a near perfect or NOS IH hubcap for the front of my 149. Want to replace my scratched one. Please contact me at: [email protected]

 

[belliott]

I am looking for a Quietline muffler. Also if anyone has the aluminum casting for the muffler box and the sheet metal for sale I would be interested.

Thanks!

 

[dschwandt]

WANTED: A pair of rubber headlight mount rings for a QL.

 

[sblunier]

Wanted:

Dual hydraulic valve and lines for Cyclops series of tractors, preferrably off of a SGT, but really need the valve and front lines.

Email in profile. Thanks.

 

[jharder]

Still looking for the following items. A good running engine for a 482. And the 3 tractors 182,1282, and a 782d. I am in Ohio 60 north of Columbus and the same from Toledo and willing to travel to In.Mi.Ky.Wv. Somewhere around 200 to 250 miles away would be all right. Email in profile. Thanks Jim

 

[mmasheris]

Injput gear for creeper drive ,the one that goes on the trans

 

[bwittman]

I am looking for a battery hold-down bracket and a tie rod for a Quietline. Brian Wittman [email protected].

Thank you.

 

[ahallman]

Hi,
I have a H42 Snowthrower and a Cub 1641.

I'm looking for a hydraulic Lift Control Lever as shown in the manual. I attached a picture below. I can't find a part number for this, so if someone has that information, that'd also be helpful.

Please email me at [email protected]

 

[sbauer]

Looking for the 7" pulley for a 364 snowblower. The part number is 756-0442. I need it to make the blower spin fast enough for a 782.

 

[rmcshane]

Well, once again I am in the market for another 73 Cub Cadet, preferably non running but complete. If it runs, that's ok too, but I want it reasonably priced. Located in Springville IA. Please email me (in profile). Thanks.

 

[belliott]

I am looking for the following parts:

• Mule drive adjustment lever that attaches to the right pulley
• Muffler (2 needed)
• Muffler enclosure including aluminum casting and tin
• Front rim
• Fuel tank (I may only need the valve and grommet – I have to measure it)
• Air filter complete with engine half including three mounting screws, cover including rubber seal and rubber hose that goes to the blower housing
• Cooling fan
• Self-aligning ball bushing on hydro end of driveshaft
• Choke cable (looking for one with a black handle that isn’t faded)
• Throttle cable (looking for one with a black handle that isn’t faded)
• Hydro lever compete with black end (not faded, decent chrome)
• Hydro speed stop
• Hydraulic lift lever complete with linkage to valve (looking for one with good chrome and plastic)
• Key switch
• Headlight switch
• PTO switch
• Tractor wiring harness
• Seat
• Battery hold-down, complete (2 if you have them)
• Tail lights, complete

Please PM me if you have any of these parts for sale.

Thanks,

Bob Elliott

 

[vthomley]

Bob Elliott - I have all these parts in my shed however I'm not sure what model Cub Cadet, or models, you need these for... My educated guess is a quietline...Also no PM ing here, just old fashion emails, etc.

Please let us know what Cub Cadet or Cub Cadets you need parts for.

Thanks!

 

[belliott]

Parts are for a 1450.

I am also looking for the following for a 1000:
• Muffler
• Muffler enclosure including aluminum casting and tin
• linkage that goes from the clutch fork to the pedal
• Choke Cable

 

[wbest]

I need the decals for the hood and the side decals for the dash for a Model 129 Cub Cadet. Let me know what you have. Thanks. William

 

[jdonovan]

Looking for a set of tire chains for 6-12..thanks in advance.Joe

 

[kmcconaughey]

I'm looking for a dipstick to fit a K301 with the oil fill dipstick located down by the points. Item number 59 in the parts drawing/list below.

 

[dschwandt]

Need a decent #26 carb for a 1000 I am resurrecting and still looking for a hydro lift arm for a 1250/hydraulic lift conversion

Dave Schwandt

 

[kshultz]

Looking for the casting of a 3-point for a wide frame.

 

[thoffman]

Kraig's "Kiler Kohler" dipstick problem reminded me that I need a GOOD "non-rattler" dipstick for a 14hp AQS. No loose flappy ones please.

 

[kmcconaughey]

A dipstick has been found! Thanks to all that replied.