• This community needs YOUR help today!

    With the ever-increasing fees of maintaining our vibrant community (servers, software, domains, email), we need help.
    We need more Supporting Members today.

    Please invest back into this community to help spread our love and knowledge of all aspects of IH Cub Cadet and other garden tractors.

    Why Join?

    • Exclusive Access: Gain entry to private forums.
    • Special Perks: Enjoy enhanced account features that enrich your experience, including the ability to disable ads.
    • Free Gifts: Sign up annually and receive exclusive IH Cub Cadet Tractor Forum decals directly to your door!

    This is your chance to make a difference. Become a Supporting Member today:

    Upgrade Now

Recent content by 1811Cub

Advertise with us
cadet connection
cub cadet used parts
Shop deals on ebay
IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. 1811Cub

    howdy

    The same front axle assembly was used on several years/models. One of our sponsors should have one.
  2. 1811Cub

    1812 oil injected ?

    Crank seal(s) leakage is fairly common.
  3. 1811Cub

    1812 oil injected ?

    You will need at minimum: quantity of two KH-52-055-01-S gaskets KH-231419-S filter lower cylinder valve KH-52-035-02-S
  4. 1811Cub

    Parts For Sale Headlights

    thooper Member Joined Nov 10, 2007 Last seen Sunday at 2:50 PM
  5. 1811Cub

    power steering for 1811

    Not directly. You could put something together using some parts from a 1862/1864 and the same era super garden tractors, but the conversion is not for mechanical novices.
  6. 1811Cub

    1812 oil injected ?

    I would make sure the breather reed valve and filter is clean and working properly. Worst case is there is excessive cylinder blow-by that is overloading the crankcase ventilation system.
  7. 1811Cub

    New member PA Frank

    Welcome from Elkland Those transaxles are notorious for failure. No new parts are available. You will need to source a good used unit. Check our sponsors.
  8. 1811Cub

    1862 cyclops engine or rear end

    Probably had several thousand hours on the clock. That is what the KT17's will do too.
  9. 1811Cub

    1862 cyclops engine or rear end

    The M18 is an improvement even over the Series II KT17 it replaced. The only negatives I have with the M18 is the thirst for fuel, and the governor gear.
  10. 1811Cub

    1862 cyclops engine or rear end

    The engine is easier to pull.
  11. 1811Cub

    Does my 42" mower deck need a tensioner pulley?

    It would be helpful if you could provide the model number for the deck. There should be a tag riveted to the deck. There were at least 3 variations of the 42" deck that fit the 104. Most of the idler parts are still available new. The idler arm might be the only one you will need to source used.
  12. 1811Cub

    982 Onan engine

    The Command V twin will fit and has been transplanted in many of them.
  13. 1811Cub

    Motor oil

    Straight 30W oil has not been affected by the reduced zinc content, mostly due that it hasn't been recommended for use in cars or trucks in several decades, thus not in use with vehicles with catalytic converters.
  14. 1811Cub

    782 engine swap, wiring sanity check

    I have converted a couple of battery ignition tractors over to the magneto ignition. I replaced the key switch with one from a 582 or 1811, then re-pinned the connector and ran wiring/ deleted wiring as needed. No issues with the conversions.
  15. 1811Cub

    782 engine swap, wiring sanity check

    Yes, the Magnum's magneto shorted to ground to kill the spark, all done with the key switch and the kill wire.
See more
Back
Top