Off Topic For Sale & Wanted Classifieds

[kmcconaughey]

For sale 1973 (I think) Allis Chalmers model 620 tractor with Ark 600 loader, cast iron wheel weights, rear Cat-0 lift and PTO. Includes Cub Cadet 48", cat-0 tiller and John Deere 60", cat-0, model 260 grooming mower. $2750.00 or best offer. Includes the operator, parts and service manuals, see photos below. I have recently (last month) rebuilt the fuel pump, and carburetor. Installed new fuel line, fuel filter and fuel shut off valve. I also acid cleaned the fuel tank. (see CubFAQ#85 for the procedure) It has a new battery. I also replaced one of the hydraulic hoses on the loader and flushed and replaced the loader hydraulic fluid. Here's some photos. Email is in my profile.

SOLD!

 

[kmcconaughey]

The Off Topic For Sale/Wanted area is now set up for separate threads for each item you wish to post for sale.

 

[dschwandt]

Beacon/Morris 45,000 BTU shop/garage furnace for parts or repair
Bought new at Menards 6 years ago.
Crapped out on me last winter.
Suspect control board.
$50
Local pick up at 52041 or can help/meet you somewhere for delivery if not to far away.

 

[dschwandt]

Furnace is sold!

 

[dramsey]

The 2140 and 2145 used single cylinder Onans

That is correct, 1994-1995.

 

[dramsey]

For Sale is a Center Mount-Grader Blade
View attachment 16334
The blade is 50 inches long and 6 inches high. The frame width for center blade is 14 1/4 inches. The frame is 2 inch angle iron
Distance from front pivot pin to rear of frame is 28 inches. There is some play in the pins that controls blade position. It should be an easy fix.
View attachment 16335
View attachment 16336
The decal on the back side of the blade has the words Johnson and Horse on it.

Asking $125 if you pick up blade or $150 if I ship blade.
You can pick up snow blade at my home or I can ship the blade by Fastenal.

Buyer pays all shipping cost and assumes responsibility once it leaves my possession.

The best way to contact me is by PM.

I wish you were closer, that is for a Wheel Horse D160 and D200 and I need it

 

[buck]

Looking for a flywheel for a 1862 cub cadet with a Kohler M18. Magnets have failed in mine. Would also be interested in replacement magnets or a repairs service.

u can get magnets recharge, if they not broken up, check wi most any mag service at your friendly airport, the airport wont have this servoce but they will know where to get it done just ask any A&E, buck

 

[john.knutson]

Toro S-140 (often referred to as "snowpup") for sale. I actually had 2 running S-140s, each with some minor issues. Both had rusted chains, so I took the better parts of each and got some brand new chain to make one nice machine. It's old and loud, but it runs great and it is very lightweight.

I have it posted on Craiglist for $125, but I would be willing to work on the price a bit if anyone here is interested. I am located just west of Minneapolis, MN.

5°F cold start video:
20°F in-use video:

 

[dreinbold]

For Sale...5.5 HP Troy Built snow blower...no longer need...Starts and runs great!
Electric start...extra shear pins...tubes in tires.
Asking $200
Also...Reel mower...bought new last year for camp site and used 2 times...too small for job.

Asking $30
Can store till pick up or may be I can help deliver

 

[dramsey]

For Sale is a Center Mount-Grader Blade
View attachment 16334
The blade is 50 inches long and 6 inches high. The frame width for center blade is 14 1/4 inches. The frame is 2 inch angle iron
Distance from front pivot pin to rear of frame is 28 inches. There is some play in the pins that controls blade position. It should be an easy fix.
View attachment 16335
View attachment 16336
The decal on the back side of the blade has the words Johnson and Horse on it.

Asking $125 if you pick up blade or $150 if I ship blade.
You can pick up snow blade at my home or I can ship the blade by Fastenal.

Buyer pays all shipping cost and assumes responsibility once it leaves my possession.

The best way to contact me is by PM.

Did you ever sell this blade?