Archive through September 08, 2007

[kdortch]

Hello everyone. I'm new to the Cub Cadet forum and not sure how much I can contribute to the forum but we may see.

Currently, however, I'm in need of some Brinly Cultivator Hardware and hope you're the person(s) that has some. I'm really looking for (refer to the drawing and pic. below) Standard Keepers (Part No. C169), Wedges (Part No. C170), and Standards (Part no. C121).

If you have any of the above Brinly Cultivator hardware parts please let me know by send me an email at <<<<<<[email protected]>>>>>> Maybe we can work something out!

Thank you,
Kenneth

 

[mmiller]

I'm looking for a headlight blanking panel or a headlight assembly for a model 73.

Also, fenders for a 73.

 

[gfedwards]

Looking for a red 982 bare chassis with ID plate still intact. I only need the chassis. Would like it to be pretty close to Virginia if possible. Email me at [email protected] with info, pictures, or price. Mobile number is 434-996-5549.

 

[ndorn]

Looking for a set of rear wheel weights for a 782 so i can use a snowblower this winter and have better traction.

 

[digger]

Big D.
Do they have to be IH weights?

 

[gcoleman]

Looking for a metal W/F gas tank, as clean as possible... mine found it's way under my dads truck, go figure

 

[gcoleman]

WANTED: NARROW frame 3/4" spindles (left/right... will be painted, so old paint don't matter.)

 

[avanwettering]

Glen, I can help you on the front spindals.

 

[cwestfall]

visit my web store at www.cubclassics.com for new and used parts,e-mail [email protected]

 

[gcoleman]

Andy, what are they goin for?

 

[digger]

Glen,
Why not email Andy and ask?

 

[tbenak]

I am looking for some drive line parts for a 1200.
I need the drive hub, clutch disc and the three springs. Please email if you can help.

 

[wrwilhite]

Needed a cooling fan for a 129.

TIA

 

[taweivoda]

Kenneth, I found one of the Brinly Standard keeper #C169. I have reason to believe I have a couple more but haven't found those yet. Do you want me to send the one I have or wait until I've looked for the others.
Terry,

 

[rwilke]

William W.,
Check out Art's stuff he's selling on the "For Sale" board. He has a fan (and driveshaft) there.....

Ryan W

 

[aaytay]

Ryan-
Thanks for the sales-pitch, but that driveshaft is for a narrow frame tractor, and although that fan may work on a wideframe, it is a different design (metal) than the one William's 129 came with.

William-
The fan you're looking for can easily be purchased at any local Cub Cadet dealer or most sponsors above.

<font size="-2">I think Kraig has bought the driveshaft anyway, so consider it "sold".</font>

 

[gcoleman]

Damn deal fell through, I did get my money back, but I need the 3/4" narrow frame spindles again...
Thanks Glen

 

[kmcconaughey]

Glen, I may have steered you wrong, no pun intended, on the narrow frame spindles in a wide frame axle. The ends of the wide frame axle are taller then the ends of a narrow frame axle and the narrow frame spindles will not just "bolt in" you will have to modify them to work. The narrow frame spindles are not long enough where they fit into the cast axle ends. Note the differences in the axles and spindles.

I just thought of a possible mod for you, I'll post a rough sketch in the main forum.

 

[snelson]

I am looking for an electric PTO clutch for a 1450. I just bought this Cub, and the clutch is bad. I really don't want to pay $400 for a new one. Does anyone have one they want to get rid of?

 

[jderstine]

Need a dipstick for a K301 ( 12 hp in my 125 )

The metal cap came loose and it's oiling the front of the motor.

Price shipped to Zionsville,PA 18092
Reply here or email me JRD77VET at comcast dot net

Thank you
Jeff