Archive through September 04, 2011

[scaranci]

WANTED: Voltage regulator,15 amp stator.1974 K301, spec # 47421d,part # 4140306,superseded to 2540322. I am using the 301 to power a generator as it's the only power I have now and I am broke.I have a batt charger plugged in to keep it running. You guys don't need the details but dire straits here. If anyone near S.W.Mass has one for extremely cheap I'll hitchhike/walk to pick it up.Ph# 413-329-1635,6AM-8PM. I'm only online when the gen is running so the phone is the best way.

 

[mschuermann]

Looking for a servicable Kohler or Carter carb for my 1250. The K301 has been "Kirkized" with a milled head, ported block and 18Hp cam. I'm getting tired of readjusting the Walbro replacement carb, would like my Cub to start and run reliably again [so the Mrs. can cut the lawn too ].

 

[thoffman]

WANTED; QA38 stamped steel deck. No beaters.

 

[pdorow]

Looking for air duct for 301 ASQ,
part #KH-47-755-33 maybe the rest of the front duct work if reasonably priced.

 

[tarthurs]

im looking for the detent clip for a narrow frame creeper gear. in case my wording isnt correct im looking for the piece that goes on the shifter that holds it into gear. email me at [email protected] thanks

 

[jmills]

anybody have a set of quietline headlights with screen thanks

 

[rmastro]

I need a 3 finger clutch engagement plate for an "86" with a 7hp kohler. Also need a good PTO clutch for a "104" with a 10 hp kohler.

 

[rodsmith]

WANTED:
I.H. padlock with key!
[email protected]

 

[rciminieri]

Anybody in NY, NJ, Conn., or PA looking to sell a Cub Cadet 73 please send an email to [email protected]. I would enjoy a winter project and hope you can help. Just got all my miscellaneous needed items for my 107 from Chris at Cub Cadet Classics and I am going to need a reason to stay in the barn. Thanks Chris and Thanks to whoever can help with the next toy. Bobby

 

[dborkowski]

Wanted: Brinly 3 point hitch plow. Any condition is fine, from rusty to nice. Let me know what you have. I can be contacted by e-mail at [email protected] or at 515-402-7707.

 

[blively]

Searching for a good 82 series or QL runner to mow with. Not looking for a show piece, just a good working unit. Doesnt necessarily need to be in KY, I travel a bunch so I can pick up. Msg me with what you have, looking primarily for a 1250/1450 or a 582/682...would entertain a 782 also. Thanks for your time.

 

[wesgardner]

looking for a Lower 3point Bracket and a Brinly adapter for my 74 ih cub 128 also a hitch plate for it

 

[mbrennan]

Narrow frame mule drive with pullys. My spring side pulley bracket has worn itself a pretty large hole over the cross shaft causing the spring side pully to twist enough that the belt no longer drops straight into the pully. Anyone have a complete unit that is free of wear? The shaft is welded into the frame so replacing is a bit over my head and ability.
Thanks.
Mike at 906 788 4711 or [email protected]

 

[pburkle]

I am looking for a good set of original tires - front and back - for my 1979 1650 Cub Cadet. Please send me an email if you think you can help ! [email protected] Thanks !!

 

[gpapa]

WTB IH #1 cart. Located in the northeast is better. [email protected] Thank you, Greg

 

[sbauer]

I am looking for a cub cadet two stage snow blower for my 782 and 982. Must be within driving distance on northern Illinois.

 

[balbrecht]

I am in need of a couple of parts. 1st, a hydro control rod from a 1x9 series machine with good splines. 2nd, a WF tunnel cover cover with the hydro release flapper. Shipping would be to 54015. Thanks -Brian

 

[jbrewer]

Want good running Cub w/mower deck and 12HP or greater engine. Hydro a plus, but all models considered. Not looking for a hangar queen but a good working tractor. I'm in east central NC , but will drive a reasonable distance for the right unit.

Thanks! Pictures appreciated.

 

[mcaruth]

looking for a wide frame subframe for a dirt/snow blade. have blade, just need a good subframe. give me a hollar if you have one to sell. thanks!

 

[mcaruth]

sub frame has been found.