Archive through May 03, 2010

[bschumacher]

Hi Looking to buy a rear tailight assembly and a new steering wheel center cap for my 1965 Model 100 Thanks

 

[jschlipp]

looking for a 42" mower deck for a 149

 

[mfrade]

I need a narrow frame mule drive, just the front where it attaches to the frame. Want to make a mount for my new to me generator. Don't care if it's got the shaft / pulleys. Best price please with shipping to Massachusetts. [email protected]

 

[gpapa]

Front suitcase weight bracket for a 147 that will work with the mule drive attached. Greg 516-809-6764

 

[dgregg]

Took the rod out of my CC100. Have lots of tilling and landscape work to do with it. No time to go thru and rebuilt the engine. I need a decent engine to drop in my CC100. I'm in NW/NC Ohio
[email protected]
Thanks for looking
David

 

[jschlipp]

looking for a hydraulic valve lift lever

 

[kide]

James:
You probably will get a better chance of a response if you state what it's for ( 149??)
Als, several of the Forum sponsors part out machines.... You might want to give Charlie, Chris Westfall or others to see if they've got the lift handle..

 

[jdiederichs]

I need the hood stripe decals for a Cub Cadet 782D model. This is the International RED tractor with the Kubota diesel, the 782D only. Thanks...

 

[wshytle]

I need a Walbro carb bowl. Just the bowl. I just found a scratch on the side of the one on my 108 that is just before getting a pin hole. This is the bowl that has a lip. If you have a bad carb (Walbro) or an extra lying around please give me a shout. My email is [email protected] .

Thanks....Wayne

 

[kjgibson]

Looking for a narrow frame hydraulic lift and rock shaft for my 124.

Thanks,
Kenny

 

[gbailey]

looking for a narrow frame lift and sleeve hitch for my Cub Cadet 122.

 

[wbest]

I need a pair of the shoulder bolts with jam nuts that hold the sleeve hitch to the frame. Let me know if you have them. Thanks.

William

 

[mmiller]

I'm looking for a decent fiberglass dash for a 1x9 tractor. Thanks!

[email protected]

 

[dmull]

Need a auto relief hydro valve please, shipped to 47670

 

[syost]

I'm looking for a new wiring harness for a 149. Haven't called the sponsers yet. I thought there was someone using this site that was making new ones.

 

[lhinds]

Would like to buy a coulter for this plow. Shipped to 38556

 

[rwilke]

I'm looking for a like-new flywheel grass screen.

It covers the flywheel on my 12HP / K301 Kohler engine in my 127. Mine has broke where the four screws secure it to the pulley drive cup.

I have sent an email to a couple of our sponsors, but no response from any of them yet.

According to the parts look up, it is part# KH-235190. A new one directly from Cub Cadet is nearly $32.

If you have one, please contact me / email me with your sale price. Shipping would be to Mid-Michigan, zip code 48888.

Thanks in advance for any replies!

Ryan Wilke

 

[kweaver]

Ryan - Be patient some of them do parts as a sideline to a fulltime paycheck.

 

[rwilke]

KENtuckyKEN,
Thanks -- I realize that.

It's not a problem...my comment was not meant to bad-mouth anyone.
I only made the comment to save someone from having to remind me to, "Did you check with those listed at the top of the page?".

Meanwhile, I was looking to see if I might be able to find the part here.

Ryan

 

[rwilke]

By the way, I believe a flywheel grass screen from a 10HP (K241) Kohler is the same part as used on the 12HP Kohlers....
So if anyone has a used-but-good 10HP or 12HP Kohler grass screen, I'm looking for one.
Ryan Wilke