Archive through June 21, 2010

[jchrest]

I still have my 1968/69 125 for sale $700 or best offer. Pictures posted June 8.

John Chrest

 

[mjame]

1969 Cub Cadet 124 Tractor with a 48 inch deck. This tractor has a CREEPER GEAR. The engine was replaced and has cast iron K301/ 12 hp Kohler engine runs strong and does not knock, does not burn oil.

Has the rear lift, Correct IH lights and switch. The tractor comes with spring assist

The entire tractor was taken apart media blasted primed and painted with IH Iron Guard and looks like new.

Rebuilt Deck.
Rebuilt Starter/Generator.
New Voltage Regulator.
Clutch Disc, Throw-out bearing and Teaser spring have been replaced with new.
Rebuilt Creeper gear all bearings and gaskets have been replaced.
Rebuilt PTO.
Good Battery.
Rebuilt Steering Column.
New Coil.
New Seat.
All belts are new.
Sharp blades.
Tires are new.

Comes with a snow plow and deck $1,100.00
Also has a cadet tiller and separate mule drive for tiller that has been blasted and painted has a rebuilt 90 degree unit. Works perfect. Buyer can purchase the tractor with or without tiller, deck or plow. For everthing plus extra parts $1,500.00

 

[lbuttke]

ported hydro rearend $50.00 PICK UP ONLY NO SHIPPING

 

[mscherer]

1963 Cub Cadet Original with snow blower $350.00

 

[dhassler]

Hey Marc, is that 124 located around Connecticut by chance ?

 

[dsomers]

1980 IH Cub Cadet 782. It ran when I pulled it into the shed 3 years ago. Took battery out and tenderized it. Has front PTO and hydraulic lift for the blade in the front. The lift also raises the back attachment holder. The blade could use a good wire brushing and some paint. The mower deck is in good shape. The discus for the back is also in good shape. Needs some TLC to get her running and some wax to get the shine back. Dave 609-226-2330 New Jersey (South). Tried to attach a picture, said it was to big?

 

[dsomers]

Let me try again. I posted and forgot to put the price. 1980 IH Cub Cadet 782 red. It ran when I pulled it into the shed 3 years ago. Pulled the battery and put the tender on it. Has front PTO and hydraulic lift for the blade in the front and discus in the rear. It's complete. Blade could use a serious wire brushing and some paint. The mower deck is in good shape and the discus is also in good shape. 17 horse twin kohler engine. Needs some TLC to get her running and some wax to bring back the shine. 400.00 or BO. I tried to post a picture but it said it was to big? I'm in New Jersey. South. GSP exit 48 for you Gilda Radnor fans. Dave 609-226-2330
Thanks,

 

[aschmidt]

We are now making rims for cub cadets. We have 8 1/2 for the 23x10.5 tires and 10 1/2 for the 26x12 tires. You can get them in stock offset like factory or your own custom offset. Let me know what you need. Also many new parts on the web site. Thanks - Aaron - Xtreme Motorworks

 

[jbaker]

September of 1976= model 1200... $600.00

The Good: strong non smoking original 12hp, creeper gear, 10x23.5 rear tires, side panals, and general good shape

The Bad: needs motor iso mounts, muffler box shroud missing, needs TLC

hour meter reads 180 hours or 780 hours if turned over I am not the original owner

sorry about photo qaulity---I can be reached thru my profile email

 

[jbaker]

QA 42 snow thrower...$200.00

I have never mounted this, I do know everything turns but thats all I can see

no major problems except common rust

use my profile email to reach me

 

[jderstine]

Here's Dave Somer's 782

 

[dsomers]

782 sold - thanks all - Dave Somers

 

[bcook]

For Sale:

Brinly disk....

Currently set up as a 'rear gang', however, it can easily be converted to a 'front gang'. I have disassembled it, and fully greased it. It can be adjusted to be narrower, and to change the angle that the disks cut. Somewhere during it's life somebody decided to paint it green, and it is kinda rusty, but works fine.

This disk was made by Ohio Steel Fabricators....

This disk is set up for a 'front gang'. If you want it to be a rear gang, that is simple to do. I have disassembled it, and fully greased it, and it can also be adjusted to be narrower, and to change the angle that the disks cut. Nice original paint.

Price: $100 each-your choice......or $175 for both of them

Must be picked up at my place in west central Ohio.

If you are interested, please e-mail me at: c1450cATyahoo.com
(replace the 'AT' with the @ symbol)
Please put 'disk' in the subject line, so I don't delete your e-mails.

Thanks!
Bill

 

[mgonitzke]

I need to clean out a lot my parts, since I no longer have a tractor between my Original and my 682. Here's a few of the things I need to get out of here.

71, 102, 122, 123 lights + switch. Nice shape, but one trim ring is missing, as seen in the picture. One of the switches pictured below is included. $40

73, 106, 107, 126, 127, 147 lights + switch. Nice-looking and complete. One small crack in the plate itself is circled in red. Does not affect function. One of the switches pictured below is included. $60

Here's the switches I mentioned for the above two panels.

Headlight blockoff for 86, 108, 109, 128, 129, 149, and 169. Nice shape. $10

73, 1x6/7 and 86, 1x8/9 headlight ring
ONE headlight ring. Surely someone is missing one. $8

Rubber boot that goes between the dash and the wheel on all of the cyclops tractors. Nice shape. $5

1x4/5 dash. Halfway decent dash. Has one crack, circled in red in one picture. It wouldn't be hard to fix. Would need a bit of TLC. $15

1x4/5 dash. This one has a couple of cracks, circled in red in one pic, and a small hole cut in the right side for access to the thottle control screw. Nothing that couldn't be fixed, but will also need some work. $5

Hydraulic lift valve for Cyclops tractors. Plastic handle is kinda messed up. $10

1100? 482, 582S, 580, 1204, 1604 brake pad assembly. There appears to be a fair amount of pad material left before the rivets start touching the disc.

I have a few other things on the "For Sale" page of my website, as well. All prices are OBO, shipping not included. I also have some other stuff I need to list, like frames, 1x2/3/4/5 fenders, footrests, etc. I really have too much to list. I don't have anything particularly rare (no NF hydraulic lifts, round fenders, electric lifts, etc). Email me if you're looking for something, and I'll see if I've got one. [email protected]

 

[jderstine]

Matt G,
I will purchase the 122 headlight panel and switch.

Email sent.
Jeff Derstine

 

[mgonitzke]

1x2 lights, $5 dash, headlight ring, and cyclops control valve are sold.

 

[mgonitzke]

1x8/9 blockoff is sold. Here's some more stuff.

Cyclops 30mm Axles and Carrier. This carrier came from a rearend purchased at a dealer auction. The carrier bearing on the ring gear side got loose somehow and the inner race spun on the carrier. I mic'd the shaft where the bearing mounts, and it is worn about 1.5 to 2 thou under. This may be fixable, but I have no suggestions for how to do so. Included are the axles, carrier, and carrier bearing retainers. The price is cheap since I don't know how easily fixable it is. $60

1440, 1641, 1861, 1863 Hydro Pump. Hydro-Gear pump from the same rearend that the above carrier was removed from. I have no idea if this works or not. I suspect it would, as the problem with the rear was a loose carrier, and I am guessing that's why the transaxle was removed from a tractor. I'm also selling this cheap since I don't know if it works. $25

1440, 1641, 1861, 1863 Hydro linkage plate. Appears to be in pretty good condition. $15

Cyclops axle tubes. I have two pairs of these. One pair does not have bearings. $10/pr (w/bearings) $7/pr (w/o bearings)

86, 108, 128 dash tin. Very nice used dash tin. Light wear from use, and a couple small dents and distortion around throttle bracket holes (see second picture). $30

71, 102, 122, 123 grille insert. Solid, but covered with several layers of nasty paint. $5

105/125 hydro lever shaft
Spline is shot (see inset). Rest of it works. $5

NF hydro levers. Splines are shot. I really don't want to throw them away. You drill a hole through it and the shaft and put in a roll pin. $3/ea.

All prices are OBO and do not include shipping. Make an offer...I'd rather not have to scrap out stuff if people can use it. [email protected]

 

[mgonitzke]

CCC 580 converted to 582 w/ IH 3-speed rear.

Runs and mows nice. Has 50" deck. Two small holes were patched, deck straightened. Spindles are good and quiet. B&S twin starts easy with slight smoke on startup (clears in seconds) and if you ram the throttle forward, it'll smoke slightly as well. New clutch (new driveshaft, friction disc, throwout bearing, teaser spring, 800# red main spring, etc, pressure plates trued on lathe), new magneto, spark plugs, rebuilt carb, and several other random new parts.

This thing sat for quite awhile and the rings on the right side cylinder were stuck. I've been using it and putting MMO in the gas, and the oil consumption has dropped and the power has come back. It's a nice-running machine now. Only issue I can't figure out is it will charge intermittently. The original rectifier quit and I installed a Kohler rectifier under the dash and away from the heat of the engine. I think it's just a bad connection, but I can't find it. It still charges most of the time, and the battery stays up. Asking $425 OBO. I'll list on craigslist and feed it to the sharks there if there's no interest, so act soon.

Tractor is located in Rockford, Illinois. [email protected]

 

[bcook]

Both the Brinly and Ohio Steel disks have been SOLD

Thanks!
Bill

 

[ckasper]

I have a cub 102 that has a 12 horse in it. I believe it has a broken connector rod. Has a deck included with it. The tractor is rough from the normal wear an tear on it not from being beat. Please email or call [email protected] or call 319-936-7259 Thanks Cletus. I do have pics i can email just cant get them to fit on the site. Asking $250.00 obo