mgwin
Well-known member
What is the heat tolerance on that insulation? I would hate to see it melt and run down all over that purdy motor! 
-
This community needs YOUR help today!
With the ever-increasing fees of maintaining our vibrant community (servers, software, domains, email), we need help.
We need more Supporting Members today.Please invest back into this community to help spread our love and knowledge of all aspects of IH Cub Cadet and other garden tractors.
Why Join?
- Exclusive Access: Gain entry to private forums.
- Special Perks: Enjoy enhanced account features that enrich your experience, including the ability to disable ads.
- Free Gifts: Sign up annually and receive exclusive IH Cub Cadet Tractor Forum decals directly to your door!
This is your chance to make a difference. Become a Supporting Member today:
782D journey
- Thread starter 1811Cub
- Start date
Help Support IH Cub Cadet Tractor Forum:
1811Cub
Well-known member
Not sure. I will run it and see if it holds up.
mgwin
Well-known member
Keep your eye on it! If it starts melting, I would bet it would melt fast.
1811Cub
Well-known member
Well, after a few workouts with the engine temp approaching 200F, and subsequent heat soak exceeding that, the insulation has not melted or distorted in any way. I think it is every bit as good if not better than the original material used Kubota/Cub Cadet. I will update further if something changes.What is the heat tolerance on that insulation? I would hate to see it melt and run down all over that purdy motor!
craybartholow
Member
- Joined
- Nov 27, 2022
- Messages
- 17
Needs some help. I have a 1282, 682, 782D all cubs have a problem with the oil pressure plugs which there are two on each trans releases and spews oil out of the tiny pin hole at the top. I use the correct Hy Trans oil and Cub oil filter. When oil releases it is only from one plug. What could case this?? Any troubleshooting tips are appreciated. Could this be caused by dirty oil and oil filter? Any adjustment etc.
They are not sealing internally.
Send them off for rebuild.
Machtech in Conneaut, OH
Manta Directory
https://www.manta.com › machtech-direct
Machtech Direct · 605 Furnace Road · Conneaut, OH 44030 · (440) 499-5813.
Send them off for rebuild.
Machtech in Conneaut, OH
Machtech Direct Conneaut OH, 44030
Manta Directory
https://www.manta.com › machtech-direct
Machtech Direct · 605 Furnace Road · Conneaut, OH 44030 · (440) 499-5813.
Attachments
craybartholow
Member
- Joined
- Nov 27, 2022
- Messages
- 17
Have you used them for this service and how much did they charge. I have 6 plugs to fix.
Been a couple years but as I recall it was $75/pr return shipping included.
You might want to check with them though 1st.
I have had several sets done by them
They do both styles.
I believe they sell on the Bay as well.
The cut them apart and replace all the innards then weld them back together
You might want to check with them though 1st.
I have had several sets done by them
They do both styles.
I believe they sell on the Bay as well.
The cut them apart and replace all the innards then weld them back together
1811Cub
Well-known member
I've used his relief valves. They are as good as new!
Is Manhtech still in business? I can't find their website anymore. They used to have a nice website that had all there pricing information and instructions on sending in relief valves for rebuild. They also had a nice selection of parts they made for Cub Cadets as well like brass buttons for front PTO clutches and cam follower bolts for Ross steering units at reasonable prices.
they appear to be on face-book at https://m.facebook.com/qualitycubparts.
lots of small businesses use face-book in lieu of a conventional website.
hope this helps!
-C3
lots of small businesses use face-book in lieu of a conventional website.
hope this helps!
-C3
